Trailer Plugs & Wiring Products
Trailer Plugs
|
|
4-Way Flat Trailer Plugs
|
|
4-way Flat Car End, 60" Long (includes 4 scotch locks)
|
|
|
|
4-way Flat Trailer End, 12" Long
|
|
|
|
4-way Flat Trailer End, 48" Long
|
|
|
4-way Flat Trailer End, 25 Feet Long
|
|
4-way Flat Loop, 18" Long (includes 4 scotch locks)
These Can Also Be Used As Extensions
|
|
|
4-way Flat Loop, 60" Long (includes 4 scotch locks)
These Can Also Be Used As Extensions
|
|
|
5-way with Flat Pins on truck to 5-way Flat on trailer with 4' Coiled Wire (Works with 4-Way Flat Plug As Well)
|
|
|
|
4-way Flat Cover
|
|
|
|
4-way Flat Cover With LED Lights - Shows You If The Plug Is Operating Correctly
|
|
Modulites
- Uses The Vehicle's Battery To Provide The Power To Run The Lights On The Trailer
- Virtually Eliminates Additional Electrical Draw On The Vehicles Taillight Circuits
- Required For Vehicles That Cannot Handle The Extra Amperage Pulled By The Trailer (i.e., Vehicles With Lamp Out Sensors,
Special Computer Systems, etc.
|
|
Modulite w/ 4-way Flat Plug
|
|
|
Modulite HD w/ 4-way Flat Plug Wit Circuit Protection
- Handles up to 4.2 amps for Turn/Stop Circuits & 7.5 amps for the Taillight Circuits
- Has Integrated Automatic Re-settable Short Circuit and Overload Protection, to Safeguard Itself and the Tow Vehicle From Sorts and
Installation Mishaps
- Interprets/Decodes Multiplex Signal Inputs (especially BMW & Mercedes Applications)
- May Be Used On 2 or 3 Wire Systems
- No Converter is Required
- Optional Modulite Installation Wiring Kit Can Be Purchased Here
|
Click for Instructions for DT_119190 Modulite
|
Modulite HD w/ 4-way Flat Plug Wit Circuit Protection and Includes Wiring Kit
- Same As The DT_119190 Except It Includes The Wiring Kit From The DT_118151 (Fuse Holder, Wire & Connectors)
- Handles up to 4.2 amps for Turn/Stop Circuits & 7.5 amps for the Taillight Circuits
- Has Integrated Automatic Re-settable Short Circuit and Overload Protection, to Safeguard Itself and the Tow Vehicle From Sorts and
Installation Mishaps
- Interprets/Decodes Multiplex Signal Inputs (especially BMW & Mercedes Applications)
- May Be Used On 2 or 3 Wire Systems
- No Converter is Required
|
Click for Instructions for DT_119191 Modulite
|
Wiring Kit for Installing all Modulites, includes
- Fuse Holder and Fuse
- Wire to be Run From Engine to Modulite
|
|
|
|
Modulite ZCI (Zero Contact Interface)
ZCI sensor technology and direct connection to the tow vehicle battery, eliminates all electrical connection
and interference with the tow vehicle electrical system. Vehicles with 12 volt system only.
|
- NO CUTTING OR SPLICING VEHICLE WIRING!
- Isolates Trailer Light Operation from Tow Vehicle's Electrical System
- Works with 2 or 3 wire systems
- Works with PWM (Pulse Width Modulation) or Multiplexed systems requiring 2 or 3 wire hookup
- Rated for up to 4.2 amps for turn/stop & 7.5 amps for taillight trailer circuits
- Works with low side switched vehicles
- Integrated auto resetting short & overload protection
- Robust design allowsfor interior or exterior mounting
- Includes Fuse Holder & Wire to Run To Battery
|
Click for Instructions for DT_119251 Modulite ZCI
|
|
|
Trailer Plug Mounting Systems
|
|
The Following Brackets Can Be Mounted to the Bumper or They Can Be Connected to the Hitch with
the Attachement Bracket (Piece 2)
|
|
|
4-way Flat Connector Bracket (Piece 1), Includes Screws and Nuts. Only Works With 4-way Flat Plugs
Made by Draw-Tite.
|
|
|
|
5-way Flat Connector Bracket (Piece 1), Includes Screws and Nuts. Only Works With 5-way Flat Plugs
Made by Draw-Tite.
|
|
|
4, 5 and 6-way Round Connector Bracket (Piece 1), Includes Screws and Nuts
|
|
|
|
7-way Connector Bracket (Piece 1), Includes Screws and Nuts
|
|
|
|
Attachment Bracket, Long (Piece 2), Includes Clamp. Generally Used to Mount Plug To Top of Hitch.
|
|
|
|
Attachment Bracket, Short (Piece 2), Includes Clamp. Generally Used to Mount Plug To Bottom of Hitch.
|
|
|
Easy Mount Electrical Bracket For 2" Receiver
- Bracket for 4 or 5-way Flat Plug and 6 or 7-Way Flat Plug Connectors
- Simple solution for mounting wiring to a hitch
- Easy to install: no drilling, no clamps
- Notched design allows access to pin & clip
- Steel body won't break like competitive plastic products
|
|
|
Easy Mount Electrical Bracket For 2 1/2" Receiver
- Bracket for 4 or 5-way Flat Plug and 6 or 7-Way Flat Plug Connectors
- Simple solution for mounting wiring to a hitch
- Easy to install: no drilling, no clamps
- Notched design allows access to pin & clip
- Steel body won't break like competitive plastic products
|
|
Easy Mount Electrical Bracket For 2" Receiver
- Bracket for 4 or 5-way Flat Plug Connectors
- Simple solution for mounting wiring to a hitch
- Easy to install: no drilling, no clamps
- Notched design allows access to pin & clip
- Steel body won't break like competitive plastic products
|
|
|
Easy Mount Electrical Bracket For 1 1/4" Receiver
- Bracket for 4 or 5-way Flat Plug Connectors
- Simple solution for mounting wiring to a hitch
- Easy to install: no drilling, no clamps
- Notched design allows access to pin & clip
- Steel body won't break like competitive plastic products
|
|
|
|
6 & 7 Way Mounting Box for Hitches with 2 1/2" Square Cross Tubes, Includes Clamp
|
|
|
|
6 & 7 Way Mounting Box for Hitches with 3" Square Cross Tubes, Includes Clamp
|
|
|
6 & 7 Way Mounting Box for Round Tube Hitches and Square Cross Tubes Which Are Slightly Hidden, Includes Clamp
|
|
|
4-way & 5-way Flat Storage Box
|
|
|
